OVS-TEST(8) Open vSwitch OVS-TEST(8) NAME ovs-test - Check Linux drivers for performance, vlan and L3 tunneling problems SYNOPSIS ovs-test -s port ovs-test -c server1 server2 [-b targetbandwidth] [-i testinterval] [-d] [-l vlantag] [-t tunnelmodes] DESCRIPTION The ovs-test program may be used to check for problems sending 802.1Q or GRE traffic that Open vSwitch may uncover. These problems, for exam‐ ple, can occur when Open vSwitch is used to send 802.1Q traffic through physical interfaces running certain drivers of certain Linux kernel versions. To run a test, configure IP addresses on server1 and server2 for interfaces you intended to test. These interfaces could also be al‐ ready configured OVS bridges that have a physical interface attached to them. Then, on one of the nodes, run ovs-test in server mode and on the other node run it in client mode. The client will connect to ovs-test server and schedule tests between both of them. The ovs-test client will perform UDP and TCP tests. UDP tests can report packet loss and achieved bandwidth for various datagram sizes. By default target bandwidth for UDP tests is 1Mbit/s. TCP tests report only achieved bandwidth, because kernel TCP stack takes care of flow control and packet loss. TCP tests are essential to detect potential TSO related issues. To determine whether Open vSwitch is encountering any problems, the user must compare packet loss and achieved bandwidth in a setup where traffic is being directly sent and in one where it is not. If in the 802.1Q or L3 tunneled tests both ovs-test processes are unable to com‐ municate or the achieved bandwidth is much lower compared to direct setup, then, most likely, Open vSwitch has encountered a pre-existing kernel or driver bug. Some examples of the types of problems that may be encountered are: • When NICs use VLAN stripping on receive they must pass a pointer to a vlan_group when reporting the stripped tag to the networking core. If no vlan_group is in use then some drivers just drop the extracted tag. Drivers are supposed to only enable stripping if a vlan_group is registered but not all of them do that. • On receive, some drivers handle priority tagged packets specially and don’t pass the tag onto the network stack at all, so Open vSwitch never has a chance to see it. • Some drivers size their receive buffers based on whether a vlan_group is enabled, meaning that a maximum size packet with a VLAN tag will not fit if no vlan_group is configured. • On transmit, some drivers expect that VLAN acceleration will be used if it is available, which can only be done if a vlan_group is config‐ ured. In these cases, the driver may fail to parse the packet and correctly setup checksum offloading or TSO. Client Mode An ovs-test client will connect to two ovs-test servers and will ask them to exchange test traffic. It is also possible to spawn an ovs-test server automatically from the client. Server Mode To conduct tests, two ovs-test servers must be running on two different hosts where the client can connect. The actual test traffic is exchanged only between both ovs-test servers. It is recommended that both servers have their IP addresses in the same subnet, otherwise one would have to make sure that routing is set up correctly. OPTIONS -s , --server Run in server mode and wait for the client to establish XML RPC Control Connection on this TCP port. It is recommended to have ethtool(8) installed on the server so that it could retrieve in‐ formation about the NIC driver. -c , --client Run in client mode and schedule tests between server1 and server2, where each server must be given in the following for‐ mat: OuterIP[:OuterPort],InnerIP[/Mask][:InnerPort]. The OuterIP must be already assigned to the physical interface which is going to be tested. This is the IP address where client will try to establish XML RPC connection. If OuterIP is 127.0.0.1 then client will automatically spawn a local instance of ovs-test server. OuterPort is TCP port where server is lis‐ tening for incoming XML/RPC control connections to schedule tests (by default it is 15531). The ovs-test will automatically assign InnerIP[/Mask] to the interfaces that will be created on the fly for testing purposes. It is important that In‐ nerIP[/Mask] does not interfere with already existing IP ad‐ dresses on both ovs-test servers and client. InnerPort is port which will be used by server to listen for test traffic that will be encapsulated (by default it is 15532). -b , --bandwidth Target bandwidth for UDP tests. The targetbandwidth must be given in bits per second. It is possible to use postfix M or K to alter the target bandwidth magnitude. -i , --interval How long each test should run. By default 5 seconds. -h, --help Prints a brief help message to the console. -V, --version Prints version information to the console. The following test modes are supported by ovs-test. It is possible to combine multiple of them in a single ovs-test invocation. -d, --direct Perform direct tests between both OuterIP addresses. These tests could be used as a reference to compare 802.1Q or L3 tunneling test results. -l , --vlan-tag Perform 802.1Q tests between both servers. These tests will cre‐ ate a temporary OVS bridge, if necessary, and attach a VLAN tagged port to it for testing purposes. -t , --tunnel-modes Perform L3 tunneling tests. The given argument is a comma sepa‐ rated string that specifies all the L3 tunnel modes that should be tested (e.g. gre). The L3 tunnels are terminated on inter‐ face that has the OuterIP address assigned. EXAMPLES On host 1.2.3.4 start ovs-test in server mode: ovs-test -s 15531 On host 1.2.3.5 start ovs-test in client mode and do direct, VLAN and GRE tests between both nodes: ovs-test -c 127.0.0.1,1.1.1.1/30 1.2.3.4,1.1.1.2/30 -d -l 123 -t gre SEE ALSO ovs-vswitchd(8), ovs-ofctl(8), ovs-vsctl(8), ovs-vlan-test, ethtool(8), uname(1) AUTHOR The Open vSwitch Development Community COPYRIGHT 2016-2024, The Open vSwitch Development Community 3.4 Nov 16, 2024 OVS-TEST(8)